Product Description

Product Description

Mandrel

1.According to different needs of customers: 

 Traditional spline milling mandrel
Cold rolling mandrel 

2. Processing range:
 
Length: within 15m
   
3. Spline type:
 
Single key slot
Hexagonal key
High torque rectangular key
Double keyway
Involute internal spline
Round keyway
Rectangular spline
Keyway designed according to customer requirements

4. Materials
Provide different materials to meet different needs of customers:
-Imported materials (imported from Japan & Germany)
-Domestic materials
-WR series materials
(WR6/WR8/WR9/WR10/WR12/WR15A/WR15E/WR30)

Advantages of cold rolling mandrel compared with traditional spline milling: 

It is a qualitative leap in spline machining process that the advanced cold extrusion process is used to replace the traditional mechanical cutting method. It not only improves the machining accuracy and surface finish, but also greatly improves the mechanical properties of parts.
The cold work hardening of metal after cold extrusion and the formation of reasonable fiber streamline distribution in the parts make the strength of spline much higher than that of mechanical cutting.
Through the test, the bearing torque of the mandrel processed by this process is increased by 25-30%, and the accuracy is improved by 2 levels, CZPT the international level 6 accuracy. In addition, the reasonable cold extrusion process can form compressive stress on the surface of the parts and improve the fatigue strength.

High toughness and strength
Strong comprehensive performance, CZPT to bear high torque, necessary for extruder
Fine processing, involute spline coaxiality ≤ 0.05mm

Cold rolling mandrel
Product introduction: 

     Designed for high-end users of twin-screw extruder: high torque, high strength and high precision extruder mandrel 

With the development of twin-screw extruder towards high speed and high torque, higher requirements are put forward for the strength (especially thermal strength) and accuracy of the mandrel of twin-screw extruder. Through extensive investigation and painstaking research, our company adopts pre hard alloy tool steel imported from Germany and cold rolling processing equipment imported from Europe for spline processing. After customer trial, our products fully meet the performance and quality requirements of similar high-end products imported from abroad.
Cold rolling mandrel production equipment

Comparison diagram of wear resistance and bearing maximum torque of different mandrel materials
 

2: Advantages of cold rolling mandrel compared with traditional cutting mandrel 

      Cold extrusion spline processing: 

Using advanced cold extrusion technology to replace the traditional mechanical cutting method to process splines is a qualitative leap in spline processing technology. It not only improves the machining accuracy and surface finish, but also greatly improves the mechanical properties of parts.

The cold work hardening of the metal after cold extrusion and the formation of reasonable fiber streamline distribution in the parts make the strength of the spline much higher than that processed by mechanical cutting.

Through the test, the bearing torque of the mandrel processed by this process is increased by 25 ~ 30%, and the accuracy is improved by 2 levels, CZPT the accuracy of grade 6 of the national standard. In addition, a reasonable cold extrusion process can form compressive stress on the surface of the parts and improve the fatigue strength.
 

Company Profile

 

ZheJiang Chooshin Industrial Co., LTD

Chooshin industrial co., ltd. is an international and specialized high-tech company engaged in the manufacture of polymer material processing equipment. Zeuxing is committed to the independent design and development of new technology and equipment related to polymer material processing equipment, equipment processing and manufacturing, and project complete set service business, and long-term focus on promoting the continuous development of high-end technology products and project complete set technology.

The company has rich talent reserve and technical experience in the field of polymer equipment manufacturing, and its technical development team has 20 years of experience in the development of complete sets of polymer blending and modification equipment. At the same time, it maintains in-depth cooperation with domestic universities and research institutes and advanced extruder companies abroad.

Company location

 

Assembly shop

 

Our Advantages

 

* With an experienced design and development team, the company has formed a very concentrated talent resource advantage in this field in China.
 

* Nearly 20 years of co-direction twin screw research and development and rich practice closely combined with many polymer material technology, integrating mechanical manufacturing, electrometer design and development and polymer material technology as a whole;
 

* With CNC machining center as the core, the industry leading modern production and manufacturing platform has been realized. Formed a set of design, manufacturing and application of 3 key technologies in 1 of the comprehensive advantages;
 

* Based on the research and practice of the internal relationship and process law between the modern emerging polymer material technology and polymer equipment, relying on the increasingly perfect and domestic leading test research and development center, it can realize the integration and seamless connection of theory, test and engineering application technology.
 

* Relying on the above advantages of resource integration, the company has and will continue to strengthen the ability of independent innovation and extended technology development.

 

 

FAQ

 

Q: Are you trading company or manufacturer?
A: We are factory.We have the technical production team,and the workers are all very experienced.

Q: Why choose you?
A:You can get a very fair price from us and our price can make you beat your competitors in the marke

Q: What kind of certification do you have?
A: Our products have obtained ISO9001 and CE certification,the quality can be guaranteed.

 

Screw Shaft Types

If you’re looking for a screw shaft, but aren’t sure which type to buy, you’re in luck. In this article, we’ll talk about the different types, including Threaded shank, Round head, and Machined. Once you’ve read it, you’ll know which type to buy. Then, you can decide whether you want a ball screw nut or a threaded shank.

Machined screw shafts

Besides the standard stainless steel shaft, manufacturers also provide a variety of other materials, such as titanium, bronze, and brass. In addition to stainless steel, manufacturers also provide a variety of top-coating options, including zinc, brass, and chromium. Aluminum screws are not particularly durable and are easily affected by weather. Most screw shafts feature self-locking mechanisms. They are especially useful in C-clamps, vises, and screw-top container lids.
For applications where accuracy is vital, a ball screw shaft needs to be annealed. A heat treatment can be performed on the ball screw shaft to ensure that both ends are heated evenly. In this process, the shaft will be more durable, while maintaining its high-precision properties. These screw shafts are a key component in computer-controlled motion-control systems, wire bonding, and other industries that require high-precision and high-quality performance.
Depending on the material used, screw shafts can be made of stainless steel or titanium. High-precision CNC machines and lathes are typically used to manufacture screw shafts. Various shapes and sizes are available, each with a specific application. Whether you need a small or large screw, you can find 1 to fit your needs. And since each size requires a different material, your choice of material is important as well.
In general, the materials used for machining screw shafts are steel, stainless steel, titanium, brass, bronze, and aluminum. Metals that resist corrosion are also commonly used. Other materials for screw shafts are Teflon, nylon, and nylon. You can also find threaded screw shafts in materials such as porcelain, glass, and ceramic. If you want to use your screws in a unique material, consider purchasing a customized one.

Ball screw nuts

If you have a screw shaft, the last thing you want to worry about is the ball nut slipping off. To prevent this, you can place a temporary stop in the shaft’s grooves to ensure that the ball nut does not slide off. When you remove the stop, you can then install the ball screw nut. But, before you can install the ball screw nut, you have to make sure that you have a good grip on the shaft.
When selecting ball screw nuts, it’s important to consider how much preload you need to apply to avoid excessive backlash. Preloading eliminates this problem by making the ball nut compact. It also prevents backlash, which is lost motion caused by clearance between the ball and nut. Backlash disrupts repeatability and accuracy. This is where spacer preloading comes in. You can insert a spacer between the 2 ball nuts to transmit the force to the nut. However, you should keep in mind that this method reduces the load capacity of the ball screw.
The critical speed of a screw is the maximum rotating speed before it whips. This critical speed is influenced by several factors, including the diameter of the screw shaft, the number of support elements, and the material. By adjusting these factors, you can reduce the number of components used and the amount of time it takes to assemble the screw shaft. In addition, you can also reduce the number of components and avoid stacking tolerances. However, the critical speed of plastic nuts is limited due to sliding friction.
The ball screw nut has several characteristics that make it unique. Its most prominent feature is the presence of ball bearings. These balls help reduce friction between the screw nut and the shaft. Without ball bearings, the friction would be too high to function properly. Another important characteristic is the groove profile of the nut and ball. These 2 features ensure that the ball and the nut meet at 2 points. You’ll be amazed by the results of the work of these ball screw nuts.

Threaded shank

Wood screws are usually not fully threaded because the shank has an unthreaded portion at the top. This shoulder part forces the screw to compress 2 pieces of wood, which prevents the screw from overheating and compromising the materials strength. As the screw is threaded partially up, it is not as difficult to remove as a fully threaded screw. However, it is important to note that a wood screw will not hold as tightly as 1 with a fully threaded shank.
In addition to being universal, screw threads can be of different sizes. For example, a M8 screw has a thread pitch of 1.25 mm. To avoid confusion, screw thread pitches are commonly given with a multiplication sign. For example, M8x1 means that the screw is 8 mm in diameter but has a thread pitch of 1 mm per 360-degree rotation. Those who are not familiar with these dimensions may find it confusing.
The OD of the threaded portion of a bolt is generally smaller than the OD of the nut. If the shank is too deep for the nut to fit, the threads may bottom out. This is why it’s important to use a thread-cutting bit with a small thread diameter. You can use a micrometer or caliper to measure the thread diameter. This tool will also allow you to easily identify which screw size fits where and how well.
The metric system is the most widely used. Fasteners with DIN numbers are generally metric in size. This makes them very useful for industrial settings. You can find metric-sized screws anywhere, as long as you buy them from a reputable manufacturer. These fasteners also come with a dog point, which is used for safety wire. If the screw needs to be replaced, the shank can be drilled with a hole for a safety wire or for a dog-point.

Round head

A round head screw is the most common type used for machine screws. Other common types include truss head, flat head, and hexed head. Each has a different profile and are used for different purposes. A round head screw is typically wider than a flat or a hexed head, and has a slightly rounded surface. These screws are useful for projects involving sheet metal or sheet-metal parts. Round heads are usually slightly wider than a hex head screw, and they may also be used as a substitute for washers in certain applications. However, truss heads are not necessary for every project.
A wood screw has a smooth shank that protrudes above the surface of the material it is attaching. A metal screw has a threaded shaft that is fully threaded from head to point, and a fully threaded shaft provides more bite. Two common head styles are round head and pan head. If the task requires the screw to be flush or countersunk, the round head will be the best choice.
Another type is the Reed & Prince screw drive. These are similar to Phillips screws but have a 75-degree V shape. They are commonly used in marine hardware and are also known as BNAE NFL22-070. This type is also used for steel plate hangers. In addition to round head and pan head screws, there are a variety of other screw types. You can even get a head with a slotted head if you know where to look.
Screw diameters are specified according to the ISO 261 or ISO 262 standards. An M8 screw has a diameter of 8.25 mm. The M8 screw has a pitch of 1.25 mm, which is equivalent to 1 mm per 360 degrees. There are several other standard screw sizes and thread diameters available. You can find them all by consulting the relevant standards. But remember, the metric system is the most popular.

Self-locking mechanism

A self-locking mechanism for a screw shaft is a device that secures the screw to its supporting member in a failure position. The locking mechanism provides a positive connection between the screw shaft and the control surface during normal operation, and locks the screw to its supporting member when the screw fails. Previous attempts to solve this problem have typically used secondary nuts with free play on the screw, which were intentionally designed to jam when loaded. However, such a device can be unreliable, which is why the present invention offers a more robust and reliable locking mechanism.
The self-locking function of a screw depends on several factors, including its pitch angle and the coefficient of friction of the threads. The angle of friction must be less than the tangent of the material pairing to prevent untightening of the screw. Screws with self-locking mechanisms have an efficiency e lower than 50%, which is less than half. Self-locking screws also have the benefit of being less efficient than a standard screw.
Unlike a normal screw, a self-locking screw can be turned in either direction. The nut 22 rotates with the screw shaft, and the member 23 is translated in an axial direction. Regardless of the direction of the rotation of the screw, this axial translation will result in the opposite moment to that input moment. While screw self-locking mechanisms are typically less expensive, they are more reliable and durable.
Another important feature of self-locking screws is that they are not susceptible to independent loosening. The screw cannot rotate without a certain amount of torque. In addition, a self-locking screw shaft must have a small wedge with a smaller half-angle than the arctangent of the static friction. This means that the torque applied by the driver must be greater than the torque needed to overcome the friction.